Install thermostat baseboard heater

This is offered as a frost protection. A double pole thermostat is a complete line break of both sides of the V circuit. This means when is actually off.

Most thermostats have a rating right on the package of how many watts they will handle of electricity. Most thermostats are also rated for watts. As a rule of thumb you cannot exceed W or 16 A on a standard 20 amp V electrical circuit. This is sufficient for the thermostat to supply. This means you can hook up a number heaters. From watt on word up through to Watt. You can wire your installation larger. However you will need a relay system with a low-voltage thermostat to control up the multiple circuits of W.

This can be relatively expensive in the few hundred dollar range. For more on those you can see here. Be careful on the type of thermostat that you purchase as it can slow down your Wi-Fi signal considerably. Wi-Fi thermostats are great because you can control the heating mode of your home from away or from anywhere. They should be more than willing to off the advice to you as we never recommend to do your own electrical work.

Wondering why your generator runs but no power? Then you came to the right place. Let our experience help. There are a few different reasons why your generator would run with no power. The main All lights are a little different, looking to change a bulb and wondering how to remove ceiling light cover?

We can help. Ceiling light covers are all different however the most common are set Turn the dial from high to low. If the thermostat is good, the tester remains lit in both positions. Repeat on the other set.

If the light goes out, replace the thermostat. Connect the wires you labeled "line" to the line wires on the thermostat. Connect the wires you labeled "load" to the load wires on the thermostat. Fold the wires into the box, attach the thermostat to the junction box, and reposition the cover. Replace your thermostat for a heating option that will help cut your monthly bills. We show you all the steps to this simple electrical project. June 12, Save Pin FB More. Tools Multimeter or circuit tester and continuity tester Qty: 0 Screwdriver Qty: 0.

Materials Line-voltage thermostat Qty: 0 Wire nuts Qty: 0. Before you begin, turn off power to the circuit. The Nest Learning Thermostat. See also. For one, thermostats situated in the lower 6 inches of a room are not accurately measuring temperature since cold air sinks.

Wall thermostats allow you to situate your heater's sensor higher up, near the middle of the strata of heat layers, or about 48 inches high. This position is closer to where you are and it reflects your comfort. Baseboard heater-mounted thermostats also entail bending down every time you want to change the temperature. Wall-mounted thermostats are easy to access. If you have your walls open and no drywall has yet been installed, it is highly recommended that you install a wall line voltage thermostat.

Line voltage thermostats are simple mechanical devices that connect and disconnect the power going to your heater. These thermostats act much like a dam in a stream. When the dam is open, water flows. When the dam is closed, water stops. Line voltage thermostats mechanically interfere with the flow of electricity from the power lines to the baseboard heater. When there is no connection in the device, the heater cannot turn on or off. When the connection is restored, the heater can activate.

Line voltage thermostats have a basic temperature-sensing device so that they turn on or off according to a temperature range you have set. They are inexpensive and easy to install, but you especially need to make sure you've got the wiring correct. Before you do anything, turn off the circuit and verify that no power is flowing with a voltage tester.

Since this is a V circuit, you will be turning off a double-pole circuit breaker, not a standard single-pole breaker. With your voltage tester , make certain that the circuit wiring is dead, with no current at all. Even though these are not overly sensitive chip-enabled programmable devices, you can still break them if you wire them incorrectly. Mistakes in wiring up a V switch, outlet, or even GFCI will not do much harm to the device normally, but since this is a V device that has so much juice flowing through it, you can easily damage the device or injure or kill yourself.

There are two ways to approach the attachment of the ground wire to the thermostat:. If there is no ground for the thermostat: Devices such as a Cadet Mechanical Thermostat are plastic, and thus, do not require grounding. You will wire-nut the ground wire coming in with the ground wire leaving the box, bypassing the device entirely. If you have a grounded thermostat: Does your thermostat have a green ground screw on it?

Or similarly, does it have a green or bare wire coming out of it? If so, this is the wire that connects your device to the ground, and this is crucial for safety. Wire-nut the two ground wires, adding a third ground wire.

That third ground will attach to the device or you will use the wire already on the device. If the thermostat's electrical box is metal, it also must be grounded, with a pigtail wire or with a grounded conduit path.